Upwardly mobile

After almost three years of ownership I finally got my GT6 out for a MOT and even better, it passed first time with no advisories, just positive comments from the tester about the CV conversion on the rear and the condition of the underside.

Though to put a bit of a damper on it, I did have to pull over on the way back as the car mis-fired and refused to start again, so it was up with the bonnet. As I lifted the distributor cap off, the rotor arm was not in it's proper place, so I am guessing it may have jumped out?
I shall see if I can fit a Lucas dizzy for possibly increased reliability over the old Delco unit, but the next major job for me will be getting the Megajolt system built up and fitted.

It's great to have it almost on the road, though I still need to get the tax applied for, but there is not too much of a rush as I had been hoping to fit a new water pump before the MOT, unfortunately it has still not been delivered. Apparently the address or telephone number on the package was not correct or clear enough, so the courier could not deliver it or contact me, should have gone to Fitchetts really as I know they always get parts out to me next day, oh well, we live and learn. The plan now is to try and get it to run something like right as the carbs still need balancing & adjusting and then go out and put some miles on it.

It is a bit of a shock to the system as I had not driven a small chassis Triumph in anger for over a year, it does feel a lot more steady now on the 175 tyres compared to the 155's I had on it before I went off for the MOT.

New Arrivals

Last week the new chassis for the Lightweight was delivered, ready modified to take the 200tdi engine and fully galvanised, so it ought to last a few years. Unfortunately, work on the Land Rover will be slow for a bit as we wait for some reasonable weather to get the remaining bodywork cleaned off and painted. Added to this the replacement springs, new parabolic ones, are not expected to be delivered until Christmas, so we cannot start building up the new chassis until we get those.


Later on in the week, a couple of guys came out to fit a new windscreen in the GT6. Seeing as a new screen from Moss would be close on £110, I thought that the deal I got was not too bad as two guys came out to fit it, taking 45 minutes to do the job, only cost me £100. I can't help but think they did not make much of a profit on that job.

Meanwhile, many of the smaller jobs required to get the GT6 through a MOT have been completed, with the screen wash system plumbed in and lined up and a exhaust system sealed up and clamped down.
A slightly more long-winded job was in the making of an air box. When I did the bulkhead modifications many months ago it was my intention to fit a modified Spitfire air box, not ideal I know, but it is a starting point.

Instead of trying to fill in the old holes in the Spitfire back plate and to make alignment of the new holes much easier I decided to pull apart an old GT6 air box and weld that to the back of the Spitfire one. It all looks a bit agricultural at the moment but it should at least see me onto the road. I just need to find some suitable filters to go over the end of the tubes and then it should be good to go until I get round to making something better.

Steps forward

I’ve been having another bash at the GT6, with a view to getting it MOT’d and on the road before the end of the year. Most of the big jobs that needed to be done before it had any chance of passing a MOT had already been completed, so now it has come to working through the long list of minor jobs.

One job that did cause a bit of a headache for a time was trying to get all of the lights working. With a bit of vigorous wobbling around of the bulb holder I was able to get the bulb to work for a time, but not to a point I would trust it for any length of time.
I decided to take the holder apart to clean it up and see where the weak link was. They seem to be failing where the negative contact for the bulb should mate with the larger which holds the assembly to the light unit. I have tried cleaning it all up and re-assembling it again, but that does not seemed to have improved it much.
To work around this, I ended up drilling through the two negative contacts and with the addition of a small screw, it holds the two contacts together so much better.
After getting a few other jobs out of the way, I have returned to fitting the new speedo, spending some time fabricating a bracket to hold the pick-up sensor on the diff. The bracket was built-up on the bench using a spare diff to make sure it all fitted properly before transferring it to the car. As the suppliers suggested, the propshaft bolts have been replaced with cap head ones to aid the pick up sensor.
Over the next few evening I hope to get the speedo wired up, just need to run power lines to the pick-up sensor and speedo head from the fuse box, connect the data line from pick-up sensor to the speedo and wire in the warning lights.

For the MOT, the car will just have the one seat fitted for a couple of reasons, I have not round to fitting the second seat to it's runner yet and as I have not been able to enguage the overdrive at speed yet, I would like to know it works before fitting the seat and hence making removal of the gearbox tunnel much harder.

I should have someone coming in later this week to fit a new windscreen, the current one might pass the MOT but it has so many minor scratches that it would annoy me all too quickly. Then that just leaves the screen wash system, front chassis over riders and front number plate to be fitted up before I consider booking in for a MOT.